The cylinder body of the high-speed water ink printing slotting machine can only be checked with the level, but these methods cannot be used after the installation of the equipment is completed. The general practice is to take the eraser drum as the standard core to check the level of the high-speed ink jet printer drum, which can be checked by pressing the fuse, pulling a small strip of paper or pressing the ink bar.

The surface of the cylinder body of the high-speed ink printing machine should be kept clean before it can contact with the symmetry of the stress. Therefore, the printing ink and other residues on the surface of the cylinder body should be cleaned up every time the high-speed ink printing machine is installed.

The liner at the bottom of the high-speed ink printing slotting equipment should be leveled and should be a little compressible. Therefore, it cannot be used as a liner, but can be coated paper, cloth paper, type pad paper, etc. In fact, if the surface is flat and a little compressible, how to use polyester wheel film base as the liner of high-speed ink printing machine. Because there is relative sliding between the liner of the high-speed ink printing machine and the high-speed ink printing machine and the cylinder body. Therefore, the liner surface will be damaged and its surface symmetry will be destroyed.

In addition, due to the effect of the working pressure of packaging printing, the compressibility of the liner of high-speed ink printing machine is also becoming smaller, so the liner should be replaced after a period of application. The number of overlays of the liner should be lower and higher. The thickness of the liner shall be accurately measured with a micrometer, and the information in the technical instructions shall be taken as the standard. Special attention should be paid to the fact that the surface of the gasket is not normal, so it can not be padded, only replaced.

The text on the surface of the high-speed ink printing machine will be complete, and the text should be symmetrical, consistent, and clear, so that all sections can be evenly stained with ink. In addition, the surface of the high-speed ink printing machine should be free of dirt. If you have any dirt, you should immediately remove it with a detergent. If you have dirt on a large scale, you can clean it with developer. In order to meet the above standards, the shutter speed, vacuum value and concentration value of developer roll should be standardized.

The decontamination of high-speed ink printing machine should be carried out before the machine operation. At this time, the decontamination is convenient, which is conducive to other countermeasures. However, some latent dirt on the high-speed ink printing machine will leak out during packaging and printing, so the samples should be checked frequently after starting. If the surface layer of the high-speed ink printing machine is damaged, it will interfere with the water absorption of its surface, resulting in the upper arm of the surface. For example, long-term parking, direct sunlight on the surface of high-speed ink printing machine, reproduction, etc. If it is dirty, it can be cleaned with wet powder, but some of the text and pictures are also endangered. If it still fails after cleaning, replace the high-speed ink printer.

The surface text of the high-speed ink jet printer should be vertically centered. However, because of the nonstandard high-speed ink jet printer, it should only be close to the vertical center. Taking one side as the standard, the mouth of the high-speed ink printing machine should be consistent up and down, and special attention should be paid to the size of the mouth of different models. Generally, the use instructions of the equipment should be taken as the standard. If the text and drawings are exposed to the sun, they may not print out or the surface may be dirty.

When installing the high-speed automatic flexo ink printer slotter die cutter machine, the plate clamp should be spread up and down first, and the position of the plate clamp at the mouth should be the same on both sides, which can be identified according to the ruler or other characteristic marks on the upper edge of the high-speed ink printing machine. The plate clamp at the trailing end should be put back to the smaller end. Next, the drag tip of the high-speed ink printing machine should be rolled into a 120 ° angle to facilitate insertion into the plate holder.

Prepare the liner of the high-speed ink printing machine again. After the completion of the above three tasks, you can complete the actual operation as shown below. It is better to press the mouth edge of the high-speed ink printer into the plate clamp first to make the plate edge and the clamp solid, and then clamp the plate clamp tightly. The plate clamping structure of different models is different. For clamping the plate clamp with screws, it should be tightened in the middle first and then on both sides. Pay attention to the adjustment of the thickness of the high-speed ink printing machine for the plate clamping organization.

After the installation of the high speed ink jet printer’s mouth edge, put the high speed ink jet printer liner between the high speed ink jet printer and the cylinder, pay attention to the liner should be leveled, and the mouth should be placed properly, and then press (first lock the ink roller) or learn to put down the water roller, which can make the high speed ink jet printer closely surround the cylinder, and at the same time is also conducive to the installation of the high speed ink jet printer’s drag.

When turning to the trailing position of the high-speed ink printing machine (use hand to hold the plate when rotating), stop the equipment (some equipment will stop by itself), insert the phase position of the high-speed ink printing machine into the plate clamp, and the actual operation is the same as that of its mouth. After the upper and lower parts of the high-speed ink printing machine are installed, the high-speed ink printing machine and the cylinder body can be firmly connected according to the plate support screws on the plate clamp at this time. It is better to tighten the radial plate screws on both sides of the plate clamp (especially its mouth edge).

If you are also interested in this machine,please don’t hesitate to contact us:

Overseas manager: Tom Wang

Email:cartonmachine.tomwang@aliyun.com

Phone/Wechat/Whatsapp:+86 13303078975